KILLING MAX SPRAY / HOW TO USE
ANT.
TARGET 02 / ANTHOW DOES IT WORK?
CONTACT STARTS THE ACTION.
RESULTS DEVELOP OVER TIME.
When choosing an ant killer, consider both the target and where you will apply it. Killing Max is a ready-to-use insecticide spray effective against 14 pests, including ants. Ants must contact a treated surface along their route. Identify their trail and entry point rather than treating only the ants you can see.
- 01
SURFACE CONTACT
When ants come into contact with treated surfaces along their trails, the insecticide transfers onto their bodies.
- 02
CHANGE IN ACTIVITY
Increased activity may be seen initially; this indicates that the product has started to take effect.
- 03
MOVEMENT DECREASES
Pest movement then begins to decrease.
- 24HOURS
PESTS DIE
The pests die within 24 hours.
WHERE SHOULD IT BE APPLIED?
Target hiding places and travel routes together.
- 01
Door and balcony thresholds
Hard surfaces around thresholds and under doors where ants enter.
- 02
Skirting boards and wall bases
Wall–floor junctions along ant trails.
- 03
Window edges
Suitable edges around windows where entry is observed.
- 04
Under cupboards and worktops
Kitchen cupboard bases, edges under worktops and concealed travel routes.
- 05
Cracks and pipe openings
Around gaps, cracks and pipe openings where ants emerge.
Representative ant treatment scene. Markers show suitable nearby surfaces; observe the actual travel routes and hiding places in your area.
HOW SHOULD IT BE APPLIED?
Surface spraying in an unoccupied indoor area. Ready to use; apply directly.
- 1
SHAKE WELL
Shake well before use. Release the safety lock at the tip of the spray head.
- 2
IDENTIFY THE TRAIL
Observe where ants emerge and where they travel. Target entry points and suitable surfaces along the trail together.
- 3
SPRAY FROM APPROXIMATELY 40 CM
Hold the bottle upright and spray onto ant travel surfaces from a distance of approximately 40 cm, using the amount specified on the label.
AFTER APPLICATION
Follow both the timing and the drying requirement.
- START
APPLICATION
Application is completed.
- 1HOURS
KEEP THE AREA CLOSED
Keep the relevant area closed for 1 hour.
LET SURFACES DRY
Wait for surfaces to dry. Drying time is not fixed.
- 1HOURS
VENTILATION
Once surfaces are dry, ventilate the area for 1 hour.
RETURN TO THE AREA
Use the area again only after the stated times and drying requirement have been met.
IMPORTANT SAFETY NOTEBecause the product leaves no odour, its presence may be harder to notice. Always ventilate for the stated times after application and follow the label’s safety precautions.
MONITOR RESULTS
Assess treated surfaces and the source of the problem together.
AGAINST ANTS
RESIDUAL EFFECT.
During this period, the product continues to kill ants that contact treated surfaces.
Do not wash or wipe treated surfaces. Cleaning the surface ends the residual effect.
New ants may enter from outside. While residual effect remains and the surface has not been cleaned, ants that come into contact with it are also affected. The product is not a physical barrier to entry.
If you still see ants
CHECK THE ENTRY POINT AND
TRAVEL ROUTE
AGAIN.
- Ants may be entering through a different crack or door edge.
- The observed route may lie outside the treated surface.
- The treated trail may have been wiped or washed.
- An outside source or a nest in another area may sustain activity.
Observe where ants remain active. For a severe or persistent problem, both the source and entry points may need to be assessed. Do not reapply more often than the label allows.
OFFICIAL INFORMATION
OFFICIAL LABEL AND SAFETY INFORMATION
READ THE LABEL BEFORE USE.
USE BIOCIDES SAFELY.
Ant — official label information
- Application area and method
- Unoccupied indoor area, surface spraying
- Dilution ratio
- Ready to use, apply directly
- Application dose
- 0.006 g a.i./m²
- Application amount
- 24 ml
- Application interval
- 3 months
a.i. means active ingredient. The official table lists dose and application amount separately; these values have not been converted into a number of trigger sprays.
Shake well before use. Hold the bottle upright and spray from a distance of 40 cm using the amount and method specified on the label. Keep the area closed for 1 hour; wait for surfaces to dry, then ventilate for 1 hour.
- Keep away from children, food and animal feed.
- Do not inhale vapour or spray particles.
- Do not eat, drink or smoke during preparation or application.
- Follow the instructions for use to avoid risks to human health and the environment.
- Avoid release to the environment. Toxic to bees.
- Do not apply to people or animals.
- Do not apply to food-contact worktops, kitchen utensils or exposed food.
Type 18 – Insecticide · General public use
MINISTRY OF HEALTH AUTHORISATION DATE AND NUMBER:04.11.2025 – 2025/220